Dewalt DW708 Sliding Miter Saw Dust Collection Chute
$51.00
/
This solution will replace the stock dust collection chute on one of the most popluar and robust saws - the DW708 Double Bevel Sliding Miter Saw! You will see a HUGE improvement in dust collection efficiency with this upgrade - all without compromising the capacity or range of motion on your saw.
NOTE: This solution is designed SPECIFICALLY for the DW708 model (Type 1, 2, & 3). It does NOT fit most of the DW708 Type 4 (see product pictures).
Everything you need is Included:
(1) Dust Collection Chute Body (black)
(1) Universal Hub Adapter (black)
(1) Expanding Vacuum Hose Section
(2) Flexible rubber flap
(1) Hose Transition Piece
(2) Hose Adapter Sizes (in chart below)
(4) Small phillips screws for attaching flap to the chute body
(1) Install Card with QR Code for complete installation video
| Fitting Sizes | OD |
ID |
Works with |
| Hose Transition (comes standard) | 1.625" (41.2mm) | 1.4" (35.5mm) | Small extractor hoses, Festool D27 |
| Medium Adapter | 2.00" (50.8mm) | 1.75" (44.5mm) | Common adapters, Festool D36 |
| Large Adapter | 2.45" (62.2mm) | 2.25" (57.1mm) | Shop Vac, 2.5" Dust Collection Hose |
MARC D.
The dust collection chute was easy to install and works very well. This is a great solution for my miter saw. I did take a video but I couldn't add it after uploading the photos.
Kelly T.
Great dust collection addition! easy to install and woeks far better than the stock system. Easy is catching 80%+ of the sawdust off my mitre saw. Great purchase.
Samuel L.
Great fit and finish. Works perfectly!
FRANK P.
It did not fit my saw as per advertised.
Joseph N.
Installation video was easy to follow. Everything fit as described. The amount of dust collection it permits is excellent.
Bill M.
Only gave this 4 stars because there are no directions included, or on the website, for assembly. I’m pretty handy and figured it out but others may not be.
Works exactly as it should and made a MAJOR difference in dust collection! So glad I got this upgrade!
Joseph P.
If you use secondary fence , the rubber flap will bind when operating saw.
roger h.
It is very well made and does as good a job as possible, given the geometry of the miter saw. The fences must be widened on miter cuts to allow the dust collector to pass.
The included vacuum hose adapters are appreciated, but I need one that fits a 3" Craftsman shop vac.
Jeff M.
Easy to install, works way better than the factory dust collector
Bradley O.
This is easy to install and works as advertised (~ 70% dust reduction). It integrates cleanly with normal saw operation and is a thoughtful design. I appreciate having a custom solution for my old DW708 and delight in the creativity that generated it
George H.
Good quality and fit
Scott U.
Works great perfect fit
Joel M.
It definitely collects more dust than factory collectors. I'm always looking for new ways to improve my shop. Thank you.
Ron L.
Super easy install
works great I would say it gets about 90% of the saw dust. That is SO much better then the several other methods of saw dust collection I have tried that all failed miserably, and even pretty much exploded on me .
Thank You very much for your great invention
Ron
One More Sunset Woodworking
Johnny J.
First, the dust collection chute certainly met and/or exceeded my expectations. It was simply to install and works well with the sliding miter saw. I hooked it up to my Rigid vac and I would say it collects about 85-90% of all saw dust being generated by cut. For me, that’s really good because I use my miter saw constantly and it’s been the biggest issue for creating saw dust. Very happy with it so far! And their customer service (Kerynn) is top notch as well! She went the extra mile to assist me with an issue I was having and couldn’t be happier the overall experience! I have another DeWalt miter saw that travels with me so thinking about buying another one for that saw!
Martin S.
Took a long time to get
Donna S.
Just right
David H.
Love the product unfortunately it didn’t fit my DW718 had to send it back
Warren W.
Fit very well. Just what i was looking for. Glad you guys made it for the DW708.
Douglas S.
Installation was easy. Still haven’t used it yet. Need to budget some shop time.
Thad R.
Good dust collection, sturdy construction and easy installation.
Bradley M.
Easy installation, works really well
Stephen S.
Works as advertised
Jack V.
Fit like a glove, works beautiful
Allan W.
The dust collector worked really well. When attached to my shop vac hose it collected approximately 80% of the dust.
Jim R.
works!!
Keith K.
Works well.
Mark K.
I received my order and I gotta say, it looks really nice. Much better than I thought it would to be honest.
I have not had the oppertunity to install or use it yet but looks legit! I believe it will meet my expectations if not exceed them.
Thank you Shop Nation
Robert M.
Well made parts, and easy 5 minute installation. I do suggest drilling a 1/16' hole through the rubber flap while holding it in place to make it easier to put in the four small screws which will hold the flap in place.
My first test cut seemed to collect the dust very well, but until I get into my first project will I be able to compare how much of a difference this will make overall. Hopefully I can update this review once that happens.
Roland L.
setup was easy and works just like it was meant to
Dan G.
Simple clean install. Works very well.
Jimmie B.
Was easy to install. It gets most of the sawdust. Very satisfied.
Brian F.
This was a direct bolt on unit. I could not have been any easier and it works great!!!
Kelvin A.
Everthing hooked up well. I'm going from my 4" dust collection hose to the smaller hose going to the saw collection attachment. I have lots of suction at the 4" hose, but it seems I'm loosing some of going to the smaller hose. Still works good, though, and, I'm still trouble shooting to see where, I'm loosing suction .
John R.
Only used the saw a couple times since installing the dust collection attachment but can already tell it’s awesome. I have a hood attachment to help minimize mess . Usually with original dust vac setup there is a lot of wood chips n dust in hood. With this setup I hardly had any . Shop Nation nailed it with this. I would say getting 80-90 percent of it right at the blade. Highly recommended it.
Michael A.
Had low expectations, but it actually works pretty well. Not 100%, but probably close to 90% which isn’t bad for something like this. Hopefully it holds up.
Rick H.
I installed the Shop Nation revised Dust Collection attachment on our retirement community shop's DW708 Miter Saw and received great feedback from those using that machine. A tiny bit of extraneous dust particles is all that's left... FAR BETTER than the original setup!
Michael E.
I contacted Customer Service since I can't scan a QR code by email Christmas day by email. Very surprisingly I had a reply within minutes giving me a link for the installation video. Install was easy and the collector works very well. My entire experience with Shop Nation was very good.
Timothy D M.
I have a Dewalt 708 and the factory dust collection port hooked to a shop vac was pretty bad. So the bar is low. The shop nation product is far superior and well worth the purchase.
PETER W.
I have it attached to my saw and this is well designed. I haven't used it yet but it's going to work very well. Glad I found your YouTube channel. Thank You!
Steven G.
Great product!!
tony h.
works well, not 100% dust collection but far better than the original dust collection adaptor.
Stephen B.
NA
Daniel B.
Easy installation and very effective dust collection.
Carl B.
A 30-yr problem solved in about ten minutes!! You guys hit this out the ballpark and I couldn't be happier! Thank you, guys, and keep up the great work!
Sebastian D.
Great product!
AJ J.
I had a type 4 DW708. I knew I'd have to drill and tap some holes in the saw dust cover which I did without any issues. The 3D print for the outside rim of the main dust collector body was too thin in the area where the rubber chute attaches. As a matter of fact, it came to me broken in this area about 1/3 of the way around the body. I could still attach the rubber chute, but I'm concerned about how long it will hold since it's only attached through the rubber and into the inner rim. Not sure if this is a design flaw or a quality control problem (or both) but it would be nice to have a replacement body with a fully functional rim.
James B.
Doesn’t work much better than the original, but I haven’t given up on it yet. I plan on purchasing an upgrading dust collection system that will provide better suction.
Rob H.
I couldn't find a replacement for the dust port that cracked over time. This works better than the original design. The only minor issue was that the saw blade touched the plastic when installed. A quick spin of the blade cut out the perfect size notch.
Christian H.
I would say it collects about 75 to 80 percent of the sawdust on 90 degree cuts. It collects less on beveled// or\\ cuts. Vertical 45 seems to the same as 90"s. But better then the box I had before collecting dust.
Christian
Keith L.
Good tool.
sean m.
unfortunately I would have to make modifications to my saws fence or my auxiliary fence in order to get it to cut anything other than a 90 deg cut. It looks like it would work, but I didn't want to alter either fence
Tom B.
I had to modify the dust chute by filing the saw blade gap wider to the left side as the blade was interfering with (hitting) the chute by about 1/16” or half the blade width. With the wider blade gap the assembly works great.
Michael C.
Did not fit my saw
David
Great fix for poor design on a great tool.
Dan T.
did not fit
Bernard B.
I have a variant DeWalt 708 mitre saw. A little modification was necessary to install dust hood properly. It works extremely well collecting 95% of sawdust. The installation video was excellent. Pleased with purchase.
Charles A.
This dust pick-up is well engineered and built to high tolerance. Impressive, goes together well and works great.
Hal G.
Direction of the discharge hose off the chute should be aimed more straight back and not upward. Sharp directional changes along with the corrugations of the hose slow the sawdust down. Hose Adapter fittings don't fit. Take this from a retired engineer.
Paul B.
The dust collector for my dewalt 708 works awesome. Better than I expected. The funny thing is I have the type 4 model and had to drill an hole and add a bolt in the blade housing to attach it. I selected the saw model number when I ordered it. Didn’t read further about how it wouldn’t work on the type 4 model. Glad I did. Super simple attachment and is on there rock solid without any modifications to your collector. Thanks for a solution for the worst dust collection system ever created.
Mahlon F.
Very happy with the way this fits and works!
Michael K.
I would make the 2 1/2 dust collector neck longer.
David M.
Didn't fit. I have a.
-4
Stuart S.
This is a great addition to my shop.
Thanks for coming up with this.
Patrick H.
love it
Robert B.
Months ago I watched your video on the testing and development of these vacuum attachments so I was super excited when I realized you had one designed for my DeWalt.
I have never had decent dust collection and this works better than expected!
Good job!
Andy P.
I had to use a number of different size vacuum connectors to hook up the hoses.
David M.
Fit my saw perfectly and after several sessions using I am pleased with the results. A very high percentage of dusr was collected.
Howard T.
It fit perfectly. Works great
Robert B.
I was skeptical at 1st, thinking it wouldn't fit. But after watching the installation video, it came together easily and works great!
paul s.
I installed the dust boot and the hose adapter first; then cut a hole in the side of my dust collection cabine. Then installed a Rockler 2" to 4" blast gate and ran it to the other 4" port on my Jet big dust collector. I tried to send you pictures, but i wasn't able to send them. I think i could send them if i have your email address. Love your produt!!!
Andrew S.
Plastic broke immediately. Also did not fit properly. Really disappointed!
PJ F.
Cool product!
Charlie W.
It fit perfectly and the installation vide was very helpful. It makes a huge difference on my dw708 I couldn’t be more satisfied
Thanks
Charlie
Thomas B.
Works very well. Big improvement over the stock collection system. Only negative comment is that it did not attach to my saw like the directions said to do. I had to modify my saw to make it fit. D it works well.
Brian P.
A marked improvement, thank you for spending time to design it.
Cathy B.
I have a type four.The dust shoot does not fit a type four
Paul
Fantastic product, fits and works a dream, highly recommended
David R.
Seems to work ok but the suction of my very old rigid shop vac sucks in the flaps (collapses them). I have to relieve the suction by slightly disconnecting the hose. Kinda janky.
Mike K.
Fits perfect
kathleen m.
Does not fit and was told it was the right size
John E P.
This was easy to install. Works great, helps collect approximately 75% more dust and particles than extraction over bag port.
Thomas C.
My miter saw is one of the biggest dust makers in my shop. I only put the adapter on my saw and did a couple of test cuts but the volume of dust generated was exponentially reduced!
Paul G.
It fit and no issues will report back on how it works
Clive a.
Loved the look of this. It would cut out the du a t. Only problem so far I don't have the correct fitting to attach to my shop vac. Secondly there are no instrjction for install and a list of fitting required to attach would have helped. But so far I am happy.
Dorothee N.
My husband is very pleased with the new attachment
carroll h.
My saw is a DW 708 model 4. It does not fit. I have sent it back
Eric R.
Fit perfectly, and works amazing. Really cut down on the dust my miter saw produces.
Michael R.
I’ve had my DeWalt miter saw for years and had grown tired of it spraying my shop with dust no matter what I did. When I heard about your product I knew I had to try it but still had pretty low expectations from previous attempts. Today I was thrilled when milling materials had had almost no dust coming off the saw. What a great, simple and elegant design. I can’t thank you enough.
Brian F.
Had the wrong type 708 did not fit my fault eyes were bad and could not read the small print on the saw identified tag. Back to using my festool vac.
Tom T.
big improvement on my old dewalt!!
Terry N.
It essentially easy to install and works well.
Jamie G.
Makes a noticeable difference. Helpful for a cleaner work space.
Mark F.
Excellent instructions and a very good fit to my DW708. My ShopVac has a larger hose but the transition coupler included in the kit fits perfectly. The locking lugs twist into a very secure fit, no tape or clamps required. It appears that 90-95% of the sawdust is caught.
Daniel L.
Works and fits great. Now my shop will stay cleaner. Thank you.
Joe D.
Had to return it because I didn't read every word. I have a type 4 dw708 which it doesn't fit. Otherwise it looks like a well designed and thought out piece.
David T.
Well made. It perfectly works great.
James C.
Easy installation. Perfect fit. Does an excellent job on cuts the are “one board” thick. When I stack 3-4 boards to cut at the same time, dust collection is significantly diminished. Light amounts of dust spread across the saw and wood being cut.
It is still worth the money.
Dennis F.
Easy to install and reduced dust by about 90%. Highly recommend!
Joseph C.
Installation was straightforward. Does good job of keeping down dust. Good item!
Support
Question about a product or compatability? We're here to help. Check out the FAQ page
Quality
All products and plans are produced at the highest quality.
Secure Payment
Your payment and personal information is secure.